Velour Satin backed Blankie

So Boo (our almost 2 year old), fell in love with a blanket I made her when she was a few months old. It is a velour blanket with a satin self binding back. She is attached to it so much so that it was becoming hard to wash it. My timing had to be just right so that it would be clean and dry at both night time and nap time.  So just this last week I made her a second. She calls it her "Kiki," which is about the cutest thing ever right?

This time when I made it I took some pictures of how I did it. Not the most impressive of projects but a quick easy one to do and makes a nice baby shower gift too.

-First gather your supplies.
-1 yard Velour or Minky fabric (I'm using bubble velour)
-1.5 yards Crepe Back Satin (it has kind of a cotton backing on it and is machine wash and dry able don't confuse it for the satin in the dress/apparel section).
-Coordinating thread.
-Tape measure
-Pins
-Scissors

Pre-wash your fabrics!!! This is so important or else you will get shrinking of different amounts when you do launder your blanket (and baby blankets get laundered A LOT). Then iron the satin fabric.

Triangle method for square cutting.

For my blanket I chose to make it square about 36"x36" and it has a 2" satin binding trim around it. So for cutting the fabric I measured a 36"x36" square from my velour fabric. I did this by folding a triangle with my fabric and checking the 2 sides adjacent to the right angle were both 36." ( I forgot to take a picture of this but it looks just like the picture for the next step only with the bubble velour fabric.)

The satin it needed to be 4' larger on all sides. You can either lay out your satin with the velour on top and measure 4" around all sides and cut or used the same method as above (with the triangle) and make sure your 2 sides adjacent to the right angle are both 44" (36+8).



Now lay your 2 fabrics down and center the velour on top of the satin with the wrong sides together.

Conrail you can thank me for the plug latter.

With a ruler measure that you have 4" on all sides of your satin fabric. It is also important to make sure your satin is lying flat or you will get lumps and bumps in your backing once sewed. Trim any extra if you have it.







To make the binding just fold your satins raw edge to the edge of the velour...

and then fold it over one more time.










For the corner it is easiest just to show you a picture. But here's the best way I can think of to describe it. Fold the edge you have been working on all the way to the end of the fabric. (As if more blanket was there but it is the 4" of satin on the next side)

Now make a corner by laying the outer edge of the binding fabric along the new edge (the next side) right along the velour fabric.

Then fold your next sides raw edge in to the velour.

Then over again (like you were doing for the binding originally) to form your corner.

 Pin, Pin, Pin to hold the corner. Continue folding in the binding till all 4 sides are done. The more pins the better to hold the slippy silky fabric in place and keep it from causing unsightly bulges in your stitching. (My picture doesn't have enough pins, I added more and should have added even more cause I had a few tucks in the satin when I stitched).

Speaking of stitching. Now is the time. Stitch with a straight stitch about 1/8"-1/4" from the edge of the binding starting in a corner. I just lined it up to the edge of my presser foot cause that was easier. A walking foot may have made this easier but I don't have one. So I just had to make due with what I had.

That's all you have to do, but if you choose to you can use a ladder stitch to close the mitered corners on the binding. I haven't done this on either of my blankets and it hasn't been a problem.

Hope your little one enjoys the blanket.